Actually eco tank printers are also designed to fail as they have ink pads that can only be replaced by the manufacturer I recommend you watch this video explaining the problem with tank printers like the eco tank.
That’s an ink absorber, and all inkjet printers have them. It’s not “designed to fail”, it’s a physical limitation of the universe. You can’t just keep dumping ink into a sponge forever. Eventually it will become saturated and you can either clean it or replace it.
I’ve had my printer for about four years and haven’t needed to replace one yet. They only cost about $10 when you do need to replace it. If they cost several hundred dollars, I would see your point, but the savings in ink more than makes up for having to replace a sponge every decade or so.
What I meant by “designed to fail” is that most of these ecotank printers need the counter to be reset by epson themselves. You can easily replace the pads. But you can’t easily reset the counter. It is possible but it involves trusting sketch sites and paying for a license to use the reset software. Older cartridges based epson printers had waste tanks with chips so that it could know when it was replaced. Newer eco tank printers don’t have the chip that let’s it know when the waste tank is replaced.
That’s not designed to fail, that’s designed to be serviced. Do you call cars “designed to fail” because they need new oil filters and the check engine light comes on when you need an oil change?
Yeah but it’s the same as if the oil filter in your car was super glued in and the dealership was the only ones that had the chemical to dissolve the glue.
You just said there are other ways to do it besides Epson. There are multiple sites that provide utilities to reset the counter.
The sponges are cheap. Way cheaper than using a cartridge printer. You can even just clean out the sponge and put it back in. You don’t have to buy a new one.
Even going through Epson’s first party maintenance program is way cheaper than using a cartridge printer. Like, orders of magnitude cheaper.
It’s not designed to fail. It’s designed to be user serviceable. You can buy a replacement and replace it yourself. It literally only requires a Phillips head screwdriver to take out the one screw on the back panel. If that is designed to fail, then a car needing an oil change is “designed to fail”.
It is made out of materials that have a set lifetime or propensity for easily breaking, like glass screens that explode into a supernova if you look at them wrong.
Actually eco tank printers are also designed to fail as they have ink pads that can only be replaced by the manufacturer I recommend you watch this video explaining the problem with tank printers like the eco tank.
That’s an ink absorber, and all inkjet printers have them. It’s not “designed to fail”, it’s a physical limitation of the universe. You can’t just keep dumping ink into a sponge forever. Eventually it will become saturated and you can either clean it or replace it.
I’ve had my printer for about four years and haven’t needed to replace one yet. They only cost about $10 when you do need to replace it. If they cost several hundred dollars, I would see your point, but the savings in ink more than makes up for having to replace a sponge every decade or so.
Edit: I missed that you said only the manufacturer can replace it. That’s not true. It’s user replaceable with a Phillips head screwdriver.
Edit 2: Added links.
That’s fine, but make it easily user replaceable then!
It is? It’s behind a panel on the back of the printer. Just take the single Phillips head screw off.
What I meant by “designed to fail” is that most of these ecotank printers need the counter to be reset by epson themselves. You can easily replace the pads. But you can’t easily reset the counter. It is possible but it involves trusting sketch sites and paying for a license to use the reset software. Older cartridges based epson printers had waste tanks with chips so that it could know when it was replaced. Newer eco tank printers don’t have the chip that let’s it know when the waste tank is replaced.
That’s not designed to fail, that’s designed to be serviced. Do you call cars “designed to fail” because they need new oil filters and the check engine light comes on when you need an oil change?
Yeah but it’s the same as if the oil filter in your car was super glued in and the dealership was the only ones that had the chemical to dissolve the glue.
You just said there are other ways to do it besides Epson. There are multiple sites that provide utilities to reset the counter.
The sponges are cheap. Way cheaper than using a cartridge printer. You can even just clean out the sponge and put it back in. You don’t have to buy a new one.
Even going through Epson’s first party maintenance program is way cheaper than using a cartridge printer. Like, orders of magnitude cheaper.
It would be nice of them to sell replacement kits, though
https://epson.com/Accessories/Printer-Accessories/EcoTank-Ink-Maintenance-Box-T04D100/p/T04D100
Or
https://epson.com/Accessories/Printer-Accessories/EcoTank-Ink-Maintenance-Box-T04D000/p/T04D000
It is designed to fail. But for other reasons and by different mechanisms.
It’s not designed to fail. It’s designed to be user serviceable. You can buy a replacement and replace it yourself. It literally only requires a Phillips head screwdriver to take out the one screw on the back panel. If that is designed to fail, then a car needing an oil change is “designed to fail”.
Literally rocket science. I’m gonna have to pay a monthly subscription so a service tech can come out and do it for me.
It is made out of materials that have a set lifetime or propensity for easily breaking, like glass screens that explode into a supernova if you look at them wrong.
What materials could be used here that wouldn’t have that problem?
A fair market?
The market will magically make a better material? Are you a libertarian?
Ok, at this point I feel like you’re just joking. If not, you’re legitimately mad.
Yes, planned obsolescence is madness, MADNESS!
Here is an alternative Piped link(s):
video
Piped is a privacy-respecting open-source alternative frontend to YouTube.
I’m open-source; check me out at GitHub.