• remotelove
    link
    fedilink
    English
    arrow-up
    12
    arrow-down
    3
    ·
    1 year ago

    It could be a few things. Check all the things.

    • lando55@lemmy.world
      link
      fedilink
      English
      arrow-up
      13
      ·
      1 year ago

      This is a good start, but if you check all the things and the issue persists, check other things.

      • remotelove
        link
        fedilink
        English
        arrow-up
        6
        ·
        1 year ago

        Very true! It’s those other things that can sometimes bite you.

    • atocci@kbin.socialOP
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      Thermistor is the only thing that I can think of… Hopefully tightening it works. It doesn’t happen unless the print head is in motion, which makes me think that’s the problem. Otherwise, the temperature is stable and completes PID tuning without issue.

      • remotelove
        link
        fedilink
        English
        arrow-up
        7
        ·
        edit-2
        1 year ago

        It could be a loose wire, or a one that is about to snap off. If the cable is bad or on the way out, it could easily be screwing with the resistance measurement. I wouldn’t think that just a loose thermistor could cause that mess of a graph, but who knows.

        It’s the motion bit that you mentioned that gave us just a little more data.

        If you can isolate the wire for the thermistor, jiggle it around at different points to see if you can replicate the rapid temperature changes.

        • atocci@kbin.socialOP
          link
          fedilink
          arrow-up
          2
          ·
          1 year ago

          Hmm, I might have to order a new replacement and see if that helps then. I had replaced the hot end assembly with the spare that came with the printer a couple weeks ago. I was very careful with the change, but I suppose it’s possible I damaged a wire in the process. It’s been running smoothly since then though, until today when the temperature started swinging wildly.

          • remotelove
            link
            fedilink
            English
            arrow-up
            4
            ·
            edit-2
            1 year ago

            Yeah, something got loose or broken. Try your best to isolate the fault while you wait for a replacement though. It’s always good to know absolutely sure what happened to hopefully prevent the issue again in the future.

    • atocci@kbin.socialOP
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      I assume so? The original hot end came with it pre-applied, so I think the spare the printer came with should too, but I haven’t checked this one.

  • morbidcactus
    link
    fedilink
    English
    arrow-up
    5
    ·
    1 year ago

    That looks like what I’ve had with bad thermistors or wiring on the edge of totally breaking, surprised it didn’t trip any thermal protection, when that happened on my prusa it estopped and my Voron did as well. I def recommend keeping a pile of thermistors with microfit connectors, they’re pretty cheap and they can go bad, it’s an easy debug step to swap a thermistor out to rule out wiring issues.

    • atocci@kbin.socialOP
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      It did actually, this screen shot was taken immediately before it shut down. I’ll pick up a few replacements and try swapping it out.

  • ShadowRam@kbin.social
    link
    fedilink
    arrow-up
    1
    ·
    1 year ago

    No, that’s interference from a higher current source.
    Most likely your stepper motor wires run in series with the thermistor.

    • atocci@kbin.socialOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      Looking at how the wires are plugged in, you might be on to something here. The extruder stepper seems to be wired into the same port as the breakout board that the thermistor is connected to. If that is the problem though, any ideas how can I fix it and why it’s only showing up now? I’ve had this printer for maybe 2 years now and I installed klipper on it last month, but this issue only began a few days ago.

        • atocci@kbin.socialOP
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          I replaced the hot end assembly a couple weeks ago, but I didn’t make any changes to the way things were wired. I plugged it in to the same connectors as before.

            • atocci@kbin.socialOP
              link
              fedilink
              arrow-up
              1
              ·
              1 year ago

              Yeah the exact same, it was the spare that came with the printer. I had messed up the original a little while ago when I changed out the nozzle from a V6 to a MK8 before I knew they were meant for different hot ends. The threading was the same and I thought that meant they were compatible… It had plastic leaking from around the heater block after that and after not using the printer for a bit, I did some research into where I went wrong and how to swap the parts out for the clean spare.

              • ShadowRam@kbin.social
                link
                fedilink
                arrow-up
                1
                ·
                edit-2
                1 year ago

                Sorry, I’m a little confused.

                So you attempted to replace the nozzle or the hotend at first?

                and when you had a problem you replaced the hotend?

                • atocci@kbin.socialOP
                  link
                  fedilink
                  arrow-up
                  1
                  ·
                  1 year ago

                  Yeah that’s right, I bought the wrong nozzle and using it messed up my hotend. Replacing the whole hotend at that point was easier than trying to clean the plastic out from all the places it had leaked into.